karma1959
Max Output Level: -80 dBFS
- Total Posts : 515
- Joined: 2008/10/31 10:56:29
- Location: Brooklyn, NY
- Status: offline
Audio Metronome stopped working when settings were modified & all FX were bypassed
Encountered an interesting thing yesterday during tracking - changed my audio metronome setting (just changed the type of sound it was using and DB level) and it wouldn't work after that. Tried resetting audio engine, restarting Sonar, checked it was still routing properly to the metronome bus and wasn't muted, etc.. all to no avail. Since I was tracking, I had all FXs bypassed, using the FX bypass button. I clicked it again, temporarily enabling all FXs and the metronome worked again. Bear in mind, I wasn't using a MIDI device for an eternal click, I was definitely using the internal audio metronome. I recreated this issue a few times to be sure - if the disable FX button is enabled, any modification the audio metronome settings causes it to stop working. Re-enabling all FX (or re-enabling them and immediately disabling them again straight away - either is fine) causes it to start functioning again. Can someone else confirm this issue manifests itself on their DAW? If so, I'll fill out a bug report.
Sonar Platinum x64 on Win10 64, Dell T7400 w/ 8 Xeon cores, 8 Gbyte RAM, 3 hard drives, RME Fireface UFX, UAD-1, Mackie Control, Adam A7X
|
57Gregy
Max Output Level: 0 dBFS
- Total Posts : 14404
- Joined: 2004/05/31 17:04:17
- Location: Raleigh, North Carolina
- Status: offline
Re: Audio Metronome stopped working when settings were modified & all FX were bypassed
2016/12/27 12:56:52
(permalink)
Perhaps the note of the new sound isn't mapped to that particular synth the met uses?
|
karma1959
Max Output Level: -80 dBFS
- Total Posts : 515
- Joined: 2008/10/31 10:56:29
- Location: Brooklyn, NY
- Status: offline
Re: Audio Metronome stopped working when settings were modified & all FX were bypassed
2016/12/27 13:00:09
(permalink)
Nope - I was using the 'internal audio metronome' option, not a synth mapping. When changing the settings, all I needed to do to recreate the issue was to change one of the sounds to a sound already working. For instance - in 4/4, the first click is a higher click and the subsequent 3 are a slightly lower pitch (and I had the first click set at a slightly higher volume to make it stand out). This is the way I've always used it for years. Just changing the initial click to be the same sound and volume as the remaining 3 (which were functioning fine), caused it to suddenly stop working.
Sonar Platinum x64 on Win10 64, Dell T7400 w/ 8 Xeon cores, 8 Gbyte RAM, 3 hard drives, RME Fireface UFX, UAD-1, Mackie Control, Adam A7X
|
brundlefly
Max Output Level: 0 dBFS
- Total Posts : 14250
- Joined: 2007/09/14 14:57:59
- Location: Manitou Spgs, Colorado
- Status: offline
Re: Audio Metronome stopped working when settings were modified & all FX were bypassed
2016/12/28 11:52:40
(permalink)
There have been several reports of the audio metronome unexpectedly going silent, and that togging the FX Bypass on/off would fix it. In those other cases, FX Bypass was not enabled when it happened, so I don't think that's necessarily the cause, but toggling it is the cure. EDIT: Just re-read that you are able to reproduce the issue by changing metronome settings while FX are bypassed. Will check that out; any setting in particular? EDIT2: Confirmed; just changing the First Beat dB level while FX were bypassed silenced the playback metronome. Disabling FX bypass during playback brought it back, but the click was out of sync with the timeline until I restarted playback. Good catch; you should definitely report it as I don't think anyone ever previously identified the cause.
SONAR Platinum x64, 2x MOTU 2408/PCIe-424 (24-bit, 48kHz) Win10, I7-6700K @ 4.0GHz, 24GB DDR4, 2TB HDD, 32GB SSD Cache, GeForce GTX 750Ti, 2x 24" 16:10 IPS Monitors
|
karma1959
Max Output Level: -80 dBFS
- Total Posts : 515
- Joined: 2008/10/31 10:56:29
- Location: Brooklyn, NY
- Status: offline
Re: Audio Metronome stopped working when settings were modified & all FX were bypassed
2016/12/28 22:09:26
(permalink)
Thanks for confirming Brundlefly - I'll submit a bug report to the bakers.
Sonar Platinum x64 on Win10 64, Dell T7400 w/ 8 Xeon cores, 8 Gbyte RAM, 3 hard drives, RME Fireface UFX, UAD-1, Mackie Control, Adam A7X
|
karma1959
Max Output Level: -80 dBFS
- Total Posts : 515
- Joined: 2008/10/31 10:56:29
- Location: Brooklyn, NY
- Status: offline
Re: Audio Metronome stopped working when settings were modified & all FX were bypassed
2017/01/24 11:18:16
(permalink)
jfyi.. Cakewalk problem report submitted: CWBRN-68358
Sonar Platinum x64 on Win10 64, Dell T7400 w/ 8 Xeon cores, 8 Gbyte RAM, 3 hard drives, RME Fireface UFX, UAD-1, Mackie Control, Adam A7X
|