Scratchy rough PLAYBACK AND INPUT SIGNAL

Author
Post
Essentials Only Full Version
CockRock1
Max Output Level: -90 dBFS
  • Total Posts : 15
  • Joined: 2013/04/20 09:29:25
  • Status: offline
2014/01/15 03:32:11 (permalink)

Scratchy rough PLAYBACK AND INPUT SIGNAL

Forum Community -
 
I've just had the DUO capture hooked up and installed the LE1 software.  I had to troubleshoot a few things. 
 
I had some latency so I adjusted a couple of things.  I am running the MME driver.  I tried the ASIO however could not get any playback sound so I switched back to MME. 
 
The USB port input had to be changed to support the Duo Capture.  So I had to switch from 3.0 to 2.0.
 
I'm getting a real rough scratchy input signal and playback. 
 
How can I clean up the input signal?  Could it be a bad Duo Capture?
 
Thanks
post edited by CockRock1 - 2014/01/15 03:33:42
#1

4 Replies Related Threads
    CockRock1
    Max Output Level: -90 dBFS
    • Total Posts : 15
    • Joined: 2013/04/20 09:29:25
    • Status: offline
    Re: Scratchy rough PLAYBACK AND INPUT SIGNAL 2014/01/15 04:27:11 (permalink)
    Audio Buffer Playback adjustment fixed the issue. 
    #2
    Kalle Rantaaho
    Max Output Level: -5 dBFS
    • Total Posts : 7005
    • Joined: 2006/01/09 13:07:59
    • Location: Finland
    • Status: offline
    Re: Scratchy rough PLAYBACK AND INPUT SIGNAL 2014/01/15 04:36:05 (permalink)
    Try to get ASIO or at least WDM drivers working. MME is the weakest possible alternative.
    ASIO should work if you set I/O drivers respectively and check that DUO is your recording and playback
    timing master.

    SONAR PE 8.5.3, Asus P5B, 2,4 Ghz Dual Core, 4 Gb RAM, GF 7300, EMU 1820, Bluetube Pre  -  Kontakt4, Ozone, Addictive Drums, PSP Mixpack2, Melda Creative Pack, Melodyne Plugin etc.
    The benefit of being a middle aged amateur is the low number of years of frustration ahead of you.
    #3
    CockRock1
    Max Output Level: -90 dBFS
    • Total Posts : 15
    • Joined: 2013/04/20 09:29:25
    • Status: offline
    Re: Scratchy rough PLAYBACK AND INPUT SIGNAL 2014/01/15 07:09:43 (permalink)
    RE -
     
    "ASIO" is what I'm trying to set the driver to; however, the software will only allow me to use "Duo Capture Out" from the "Master Channel" for playback.  I get no signal during playback. 
     
    Thank You
    #4
    CockRock1
    Max Output Level: -90 dBFS
    • Total Posts : 15
    • Joined: 2013/04/20 09:29:25
    • Status: offline
    Re: Scratchy rough PLAYBACK AND INPUT SIGNAL 2014/01/15 08:40:24 (permalink)
    OK Got it; Just adjusted the "Buffer Size" within the "ASIO PANEL"  listed within the "Device Settings" I toggled this initially and altered the "buffering settings" after changing the driver to "ASIO" for some reason.  Eventually I realized it and adjusted it back to the original setting.   
     
    Thank You it works perfect.  ASIO is a lot better with virtually real time and no latency. 
     
    Thanks 
    post edited by CockRock1 - 2014/01/15 10:01:13
    #5
    Jump to:
    © 2025 APG vNext Commercial Version 5.1