Helpful ReplyK-System Confusion

Author
ston
Max Output Level: -71 dBFS
  • Total Posts : 965
  • Joined: 2008/03/04 12:28:40
  • Status: offline
2015/03/23 11:57:20 (permalink)

K-System Confusion

I thought I understood the principle of the K metering system (I use the more conventional Peak/RMS type metering), but recently I've been reading some stuff which makes no sense to me whatsoever.

The stuff in question talks about calibrating your monitors such that a specific SPL level is achieved when running specific test tones through your system.

Eh?  I cannot understand how the output level of your monitors has any bearing on the level of signal being monitored by a master bus K-system meter in a DAW.  So let's say I've configured my system like this, but then:

a) Move slightly further away from the monitors
b) Put in some earplugs
c) Turn the monitors down (or up)
d) Use some headphones instead

...etc.  How does any of these actions invalidate (or affect in any way) the metering which is occurring inside the DAW?

Quite frankly, I am left completely baffled by this requirement.  Perhaps it isn't really one?
#1
mettelus
Max Output Level: -22 dBFS
  • Total Posts : 5321
  • Joined: 2005/08/05 03:19:25
  • Location: Maryland, USA
  • Status: offline
Re: K-System Confusion 2015/03/23 12:09:08 (permalink)
The volume knob alone is huge... What "ruler" is supposed to be used to calibrate with?

On the cell here, but the OP sounds like the article is amiss on what/how calibrations are done. Is there a link to what you were reading?

ASUS ROG Maximus X Hero (Wi-Fi AC), i7-8700k, 16GB RAM, GTX-1070Ti, Win 10 Pro, Saffire PRO 24 DSP, A-300 PRO, plus numerous gadgets and gizmos that make or manipulate sound in some way.
#2
ston
Max Output Level: -71 dBFS
  • Total Posts : 965
  • Joined: 2008/03/04 12:28:40
  • Status: offline
Re: K-System Confusion 2015/03/23 12:33:43 (permalink)
I can't remember the link to the original article I read a few days ago, but the internet's awash with them.  Here are the first few links from a gooflz "k system monitor calibration" search:
 
https://www.gearslutz.com...fication-k-system.html
 
https://www.gearslutz.com...ibration-bob-katz.html

http://forum.cockos.com/showthread.php?t=76587

http://www.meterplugs.com/kmeter
#3
Jeff Evans
Max Output Level: -24 dBFS
  • Total Posts : 5139
  • Joined: 2009/04/13 18:20:16
  • Location: Ballarat, Australia
  • Status: offline
Re: K-System Confusion 2015/03/23 15:05:30 (permalink) ☄ Helpfulby Dream Logic Audio 2015/04/24 13:00:08
K System is about both.  It is about the levels you are working with in terms of the rms component and the digital ref level that represents your 0 dB VU level and all inside your DAW.  Many digital systems use -18 dB FS as a level that can represent 0 dB VU.  K System has three ref levels to work with and in my opinion they are well chosen. K-12, K-14 and K-20.
 
It is good to work at a common reference SPL level in your room as well.  At certain SPL levels our ears offer a flatter more even frequency response.  (Not perfectly flat but close to in a weird sort of way)  There can be discussion as to what a good SPL level might be.  I agree with Bob Katz in that 83 to 85 dB SPL  (C Weighted) is a great level for me to work at here in my studio.  (It satisfies OH&S requirements eg for 8 hour period)  It is good to monitor at a range of SPL levels in your space.
 
Your monitoring SPL level is tied to the ref level inside your system.  If you calibrate your system to K-20 and make that produce 85 db SPL level in your room then you are set.  But if you decide to work at K-14 instead then the SPL levels in your room will suddenly get louder and now be at 91 dB SPL which is loud.  So you need to knock back your monitoring level by 6 dB back to 85 dB SPL again.
 
There is more too.  About using VU meters and keeping all rms components consistent right throughout your DAW.  It greatly helps tracking because all your tracks will end up at perfect and constant rms levels.  People sweat the peaks way too much. They take care of themselves and won’t clip anywhere usually when done right.  It allows for correct ref rms levels on all your busses and finally your stereo mix too.  It makes mastering much easier and it all works perfectly with Loudness metering.
 
post edited by Jeff Evans - 2015/03/23 15:13:57

Specs i5-2500K 3.5 Ghz - 8 Gb RAM - Win 7 64 bit - ATI Radeon HD6900 Series - RME PCI HDSP9632 - Steinberg Midex 8 Midi interface - Faderport 8- Studio One V4 - iMac 2.5Ghz Core i5 - Sierra 10.12.6 - Focusrite Clarett thunderbolt interface 
 
Poor minds talk about people, average minds talk about events, great minds talk about ideas -Eleanor Roosevelt
#4
dmbaer
Max Output Level: -49.5 dBFS
  • Total Posts : 2585
  • Joined: 2008/08/04 20:10:22
  • Location: Concord CA
  • Status: offline
Re: K-System Confusion 2015/03/23 16:51:35 (permalink) ☄ Helpfulby mettelus 2015/03/23 19:34:32
 
This may help clear up all your confusion:
 
http://www.soundonsound.com/sos/may14/articles/reference-monitoring.htm
#5
bitflipper
01100010 01101001 01110100 01100110 01101100 01101
  • Total Posts : 26036
  • Joined: 2006/09/17 11:23:23
  • Location: Everett, WA USA
  • Status: offline
Re: K-System Confusion 2015/03/23 16:57:16 (permalink) ☄ Helpfulby stickman393 2015/03/26 14:57:00
ston
a) Move slightly further away from the monitors
b) Put in some earplugs
c) Turn the monitors down (or up)
d) Use some headphones instead

These are indeed 4 quick ways to completely defeat the K-system. That's because the system is about listening levels first, and absolute levels (as shown in your meters) second. The idea is to establish a consistent correlation between output level on the meters and the volume you hear through your speakers. That's why you calibrate the speakers.
 
The levels suggested for calibration are actually a little too loud for most people, so even those who follow the K-system guidelines will normally monitor at a lower volume. That's actually OK, as long as you're consistent. But as soon as you put on the headphones (or earplugs) you're no longer using the K-system as intended. At that point you're just using one of the k-system recommended RMS values as a visual target.
 


All else is in doubt, so this is the truth I cling to. 

My Stuff
#6
Starise
Max Output Level: -0.3 dBFS
  • Total Posts : 7563
  • Joined: 2007/04/07 17:23:02
  • Status: offline
Re: K-System Confusion 2015/03/23 22:30:07 (permalink)
I might not be doing this correctly...but when I mix I usually use K-14 and I listen at a minimal level. When I perform a mixdown to distribute I usually export at a higher level but still using K-14...my exported mix usually stands up well on most systems with half volume being at comfortable listening level and headroom for a lot more if desired. I just had the pleasure of talking with the guy who invented the K system   but I didn't think to ask him about that :)

Intel 5820K O.C. 4.4ghz, ASRock Extreme 4 LGA 2011-v3, 16 gig DDR4, ,
3 x Samsung SATA III 500gb SSD, 2X 1 Samsung 1tb 7200rpm outboard, Win 10 64bit, 
Laptop HP Omen i7 16gb 2/sdd with Focusrite interface.
 CbB, Studio One 4 Pro, Mixcraft 8, Ableton Live 10 
 
 www.soundcloud.com/starise
 
 
 
Twitter @Rodein
 
#7
ston
Max Output Level: -71 dBFS
  • Total Posts : 965
  • Joined: 2008/03/04 12:28:40
  • Status: offline
Re: K-System Confusion 2015/03/24 05:27:55 (permalink)
Thanks for the replies folks!  I understand what you're saying, but fundamentally disagree for a number of reasons.
 
I shall continue to use my secret weapon when monitoring (this is also the same weapon which was used to end the loudness wars!):
 

#8
batsbrew
Max Output Level: 0 dBFS
  • Total Posts : 10037
  • Joined: 2007/06/07 16:02:32
  • Location: SL,UT
  • Status: offline
Re: K-System Confusion 2015/03/24 10:34:25 (permalink) ☄ Helpfulby Dream Logic Audio 2015/04/24 13:01:41
i think you've missed an important element of this discussion.
 
even tho the 83 db (85) setting for calibrating your monitoring station may seem a bit loud...
 
it IS the level you need to meet the human condition- meets - munson-fletcher curve -  meets translation across multiple platforms.

Bats Brew music Streaming
Bats Brew albums:
"Trouble"
"Stay"
"The Time is Magic"
--
Sonar 6 PE>Bandlab Cakewalk>Studio One 3.5>RME BFP>i7-7700 3.6GHz>MSI B250M>G.Skill Ripjaws 4 series 16GB>Samsung 960 EVO m.2ssd>W 10 Pro
 
#9
mettelus
Max Output Level: -22 dBFS
  • Total Posts : 5321
  • Joined: 2005/08/05 03:19:25
  • Location: Maryland, USA
  • Status: offline
Re: K-System Confusion 2015/03/24 11:45:15 (permalink)
^^^^
 
After seeing this in more detail, the monitor portion is really more for consistency (as bitflipper mentioned). Even something as simply as the same volume knob setting (including position, etc.) for a given digital out will yield more uniform results. There are free apps for cells that will sound meter sufficiently to choose an adequate volume placement, etc.
 
Another factor which doesn't get mentioned as much as I feel it should is fatigue. Coming from a production environment, there is only so much you can push the human body before fatigue (errors) begin to appear. Not taking breaks, not enough adequate rest, distracted (or even overly focused), throw a whole gambit of "human error" into equations even with the most precise tools and working conditions available (i.e. identical environment).
 

ASUS ROG Maximus X Hero (Wi-Fi AC), i7-8700k, 16GB RAM, GTX-1070Ti, Win 10 Pro, Saffire PRO 24 DSP, A-300 PRO, plus numerous gadgets and gizmos that make or manipulate sound in some way.
#10
bitflipper
01100010 01101001 01110100 01100110 01101100 01101
  • Total Posts : 26036
  • Joined: 2006/09/17 11:23:23
  • Location: Everett, WA USA
  • Status: offline
Re: K-System Confusion 2015/03/24 12:16:44 (permalink) ☄ Helpfulby mettelus 2015/03/24 12:29:12
ston, look at it this way...
 
Yes, you (and your listeners) ultimately control loudness with the volume control. But let's say you aren't consistent with the volume you mix at. Maybe during the day you like it cranked but have to do it quieter at night to avoid problems with the neighbors.
 
Because of the equal-loudness curves batsbrew alludes to above, you perceive sound differently at different volumes, a phenomenon that will unconsciously affect all your mixing decisions. You'll end up with inconsistent mixes: too much bass in some, not enough in others; a tendency to over-compress some things and under-compress others; lost vocals, oppressive kicks, harsh guitars; mixes that don't translate well from one system to the next. Mixes that sound good loud but fall apart at low volume.
 
These can only be avoided by mixing and mastering at a consistent volume, and by correlating meter readings to what things are supposed to sound like - at that volume. That's where the calibration comes in. Once you've established a known relationship between meter readings and speaker volume, you are then free to turn the speakers up or down, knowing that you can still rely on the meters as a sanity check. 
 
The inspiration for the K-system was a previous loudness standard that had been in place for decades for motion picture exhibition. It assures that a movie's sound will be consistent from one venue to the next. Just as you want your music to be in the same ballpark as commercial offerings heard on iPods and radio, as well as being internally consistent within a collection on a CD. 
 
You can certainly get there without the K-system or R128, and it was done that way for many years. These standards are just conveniences to get you there with less trial-and-error and greater consistency.


All else is in doubt, so this is the truth I cling to. 

My Stuff
#11
jude77
Max Output Level: -68 dBFS
  • Total Posts : 1146
  • Joined: 2013/08/27 21:31:34
  • Location: South Saturn Delta
  • Status: offline
Re: K-System Confusion 2015/04/22 16:52:46 (permalink)
bitflipper:
That was as good an explanation as I've ever heard.  Thank you!!
#12
interpolated
Max Output Level: -74 dBFS
  • Total Posts : 830
  • Joined: 2015/03/26 17:34:58
  • Status: offline
Re: K-System Confusion 2015/04/23 14:55:27 (permalink)
Bob Katz has a book that explains it better and much of the plug-ins available now follow the K-System or using Bob Katz approved hardware emulations.
 
Or BK for short.
 
p.s. Also bitflippers description is very well explained.
 
post edited by interpolated - 2015/04/23 18:30:15

I have computer stuff.
 
https://soundcloud.com/sigmadelta
#13
synkrotron
Max Output Level: -22.5 dBFS
  • Total Posts : 5263
  • Joined: 2006/04/28 16:21:21
  • Location: Warrington, UK
  • Status: offline
Re: K-System Confusion 2015/04/24 05:57:05 (permalink)
Reading this sort of stuff makes me realise that I simply do not have a clue what I am doing...
 
I need to take note though, and look further into this, as I am sure I am listening to my music much too loud at times, even to the point that I am left with that ringing in the ears sensation.
 
Also, I only ever mix on headphones nowadays, on account that people around me don't want to listen to my crap any more and I do not have the luxury of a sound proof studio.
 
Thanks for all the posts above, this is all certainly food for thought and I'm sure that, in the long run, my mixes will improve (a pity the music won't) and my ears will be thankful 

http://www.synkrotron.co.uk/
Intel Core™i7-3820QM Quad Core Mobile Processor 2.70GHz 8MB cache | Intel HM77 Express Chipset | 16GB SAMSUNG 1600MHz SODIMM DDR3 RAM | NVIDIA GeForce GTX 675M - 2.0GB DDR5 Video RAM | 500GB Samsung 850 Pro SSD | 1TB Samsung 850 Pro SSD | Windows 10 Pro | Roland OCTA-CAPTURE | SONAR Platinum ∞ FFS| Too many VSTi's to list here | KRK KNS-8400 Headphones | Roland JP-8000 | Oberheim OB12 | Novation Nova | Gibson SG Special | PRS Studio
#14
ston
Max Output Level: -71 dBFS
  • Total Posts : 965
  • Joined: 2008/03/04 12:28:40
  • Status: offline
Re: K-System Confusion 2015/04/24 06:56:16 (permalink)
I understand the principle and the K system provides a good guideline, but unless you have had your own ears accurately calibrated for equal loudness and are monitoring with fresh, un-stressed ears (i.e. they're in the same ideal state as when they were calibrated), it remains a guideline only.
 
Also, to produce the equal-loudness contours in the first place relied upon people's subjective report on what constitutes "equal loudness".  You may argue that such differences are minimised by taking a large enough sample, but this is not necessary the case if the underlying mechanism which is being measured is intrinsically broken.
 
People are, in fact, very bad judges of 'equality' (or, equally, inequality).
 
This doesn't involve judgement of noise levels, but provides a useful demonstration of the principle involved IMO:
 
Fast forward to 4:35 in the following BBC documentary, presented by mathematician Marcus du Sautoy:
 
https://www.youtube.com/watch?v=GqTB7mLpiQY
 
I like to monitor across a variety of levels, sometimes using headphones, very much according to how I'm feeling, a part of which is a reflection of the state of freshness or fatigue of my ears.  This to me makes much more sense than setting a fixed level dependent upon the subjective opinion of a sample of people who are naturally poor judges of what constitutes 'more' or 'less'.
#15
bitflipper
01100010 01101001 01110100 01100110 01101100 01101
  • Total Posts : 26036
  • Joined: 2006/09/17 11:23:23
  • Location: Everett, WA USA
  • Status: offline
Re: K-System Confusion 2015/04/24 11:24:01 (permalink)
Thanks for that link, ston. It was a very enjoyable watch. It does seem to reinforce the reason the K-system exists, by showing how unreliable our senses are at determining absolute values and the need for objective measurements that are independent of human limitations. It indirectly makes a good argument for visual aids in music, which the "use your ears" crowd dismiss as crutches.
post edited by bitflipper - 2015/04/24 11:33:54


All else is in doubt, so this is the truth I cling to. 

My Stuff
#16
DonM
Max Output Level: -34 dBFS
  • Total Posts : 4129
  • Joined: 2004/04/26 12:23:12
  • Location: Pittsburgh
  • Status: offline
Re: K-System Confusion 2015/04/26 10:00:47 (permalink)
Nice stuff ... my two cents...
 
When I am teaching the K-System and monitor position in my class I describe what Jef and Bit are saying with the following analogy.
 
I ask my students to imagine using PhotoShop in a completely dark room and being asked to adjust the brightness and color levels in a digital image - then go outside to a sunlit area and perform the same adjustments.  Establishing a consistent balance between environmental light and screen energy is a necessity in such work.
 
I work on multiple client projects over weeks, months and sometimes years.  When i return to a project regardless of what stage we are in (tracking, mix, edit, master, etc) I need everything to be exactly as it was when we last worked on the project.  I carry my SPL meter with me when I move to different studios to do work. I have Bob Katz's Pink Noise file on a USB drive I carry around as well.  I can always set a quick position anywhere, possibly not perfect but close enough for Jazz.
 
Monitor position is about establishing repeatable permanent baseline relationships with the energy coming from your system and how your environment delivers that energy consistently.  Regarding the level - I've done the 83dbfs for years and have found it a bit hot for the work that I do (mostly classical)
 
Nice thread
 
-D

____________________________________
Check out my new Album  iTunesAmazonCD Baby and recent Filmwork, and Client Release
 
#17
bitflipper
01100010 01101001 01110100 01100110 01101100 01101
  • Total Posts : 26036
  • Joined: 2006/09/17 11:23:23
  • Location: Everett, WA USA
  • Status: offline
Re: K-System Confusion 2015/04/26 11:49:11 (permalink) ☄ Helpfulby DonM 2015/04/26 15:59:42
Great analogy, Don. I've never put those two things together as an analogy, despite my own experience in photography.
 
I spent 5 years working in a photo lab (remember those?). It was a professional service, so every negative was previewed and color-corrected by a human before printing. A clever device made by Kodak called a Video Color Negative Analyzer was used, which employed rotating filter wheels in front of an interlaced monochrome CRT. It was the same color-encoding system used for space exploration because it guaranteed extremely accurate color representation. A VCNA was to photography what monitors and equalizers are to audio.
 
The VCNAs were calibrated daily, and the lighting in the room where they were operated was carefully controlled for brightness and color, just as you control the acoustical environment in your mixing or mastering room.
 
My job was making sure the printers subsequently matched the VCNA color corrections exactly. Part of that entailed color-correcting the entire plant's overhead lighting, so no matter where you stood in the (windowless) production space colors looked the same. It was all about calibration and consistency.
 
I didn't appreciate how well that system worked until I took a side job at an automated lab geared for volume rather than quality. There, no such efforts were bothered with, and you didn't know what colors you'd get from photo to photo. When I mentioned this to the lab's owner, he dismissed it as irrelevant. Much the same way some amateur audio engineers dismiss speaker calibration and acoustical treatments as irrelevant.


All else is in doubt, so this is the truth I cling to. 

My Stuff
#18
Jeff Evans
Max Output Level: -24 dBFS
  • Total Posts : 5139
  • Joined: 2009/04/13 18:20:16
  • Location: Ballarat, Australia
  • Status: offline
Re: K-System Confusion 2015/04/26 16:39:04 (permalink)
Back in terms of audio I find when I work with the K system for every project especially an album where there may be a collections of songs or tracks then the consistency it provides is very good in terms of signal flow and gain structure.
 
The track count and thus mix complexity can smaller or larger but the same follows.  Keep your track rms levels all at the K Ref level.  If there are effects/chains make sure the right rms level is going in and out of every plugin.  Setup as many buses as needed but maintain the buss overall level to also be at the ref level.  Then the buses all finally meet on the stereo buss and yes it too is sitting at the perfect ref rms level as well.  Very rare clip lights anywhere to be seen even in a large mix.  VU meters do the monitoring so well.
 
Then when all this is right you turn up your speakers to 83-85 dB.  I find the SPL meter permanently in front of me pretty handy too.  Stops you from creeping up your room monitoring level.  Some genres require you work at levels louder than the norm but only for a short time.
 
Working on an album and having all the pre masters at the same rms level certainly goes a long way to making mastering much easier.   K reference levels are very close to loudness levels too. (for consistent energy tracks all the way through)
 

Specs i5-2500K 3.5 Ghz - 8 Gb RAM - Win 7 64 bit - ATI Radeon HD6900 Series - RME PCI HDSP9632 - Steinberg Midex 8 Midi interface - Faderport 8- Studio One V4 - iMac 2.5Ghz Core i5 - Sierra 10.12.6 - Focusrite Clarett thunderbolt interface 
 
Poor minds talk about people, average minds talk about events, great minds talk about ideas -Eleanor Roosevelt
#19
interpolated
Max Output Level: -74 dBFS
  • Total Posts : 830
  • Joined: 2015/03/26 17:34:58
  • Status: offline
Re: K-System Confusion 2015/04/26 17:27:05 (permalink)
Well all this talk about metering has got me reading and experimenting again. Being as I have been away from all this sort of thing for a long time and Sonar Platinum was my entry back into.
 
I was playing through the console options and notice you can specify Peak+RMS,Peak or RMS only in the different metering options. Providing you take any errors into account, you could use that in place of another meter until you installed a more detailed one.
 

I have computer stuff.
 
https://soundcloud.com/sigmadelta
#20
Paul P
Max Output Level: -48.5 dBFS
  • Total Posts : 2685
  • Joined: 2012/12/08 17:15:47
  • Location: Montreal
  • Status: offline
Re: K-System Confusion 2015/04/26 18:46:37 (permalink)
 
The Klanghelm meters are only about 8$ and are so much more obvious than the sonar meters.
 
The main thing, though, is that you can set the 0db on the meter to your reference level (say -14) instead of only lighting up the bottom of the meters where things are less accurate.
 

Sonar Platinum [2017.10], Win7U x64 sp1, Xeon E5-1620 3.6 GHz, Asus P9X79WS, 16 GB ECC, 128gb SSD, HD7950, Mackie Blackjack
#21
Jump to:
© 2024 APG vNext Commercial Version 5.1