kzmaier
Max Output Level: -81 dBFS
- Total Posts : 461
- Joined: 2010/10/18 08:20:01
- Location: Rochester, NY
- Status: offline
Silent Mid Tower PC cases
I am trying to silence my PC. I'm happy with system performance but the case is made for gaming. I currently cannot put the PC in another room so I'm looking at getting a new case. I'm looking at the Corsair Carbide Series 330R Ultra-Silent Mid-Tower Case. Anyone use these? Any suggestions welcome? My MB is a m-atx.
Thanks,
Ken
|
Starise
Max Output Level: -0.3 dBFS
- Total Posts : 7563
- Joined: 2007/04/07 17:23:02
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 08:41:08
(permalink)
☄ Helpfulby mettelus 2015/10/12 18:20:08
Here are a few suggestions that are work arounds that might enable you to avoid a new case. I have my case under my desk. The location of it makes it less loud...so maybe changing location would help. Putting sound absorption foam close to it without blocking cooling vents can help. Some of those gaming cases have more fans than is really necessary. You could try looking at your cpu temps with one or two disconnected. You can buy fans specifically made to be less noisy. Unless it was specified otherwise,he fans installed are all basic cooling fans...so you might benefit by only changing fans.
Even a sensitive condenser mic set to cardoid pattern will be hard pressed to pick up very much noise if you have the case to the rear of it and are at least 6' away especially if you happen to be higher than the case. Usually if I'm picking up noise my gain staging is too high at the front end.
Those quiet cases are mostly quieter fans with a small amount of sound insulation in the case. Some try to port the noise away...but it isn't anything you probably couldn't do yourself .
Intel 5820K O.C. 4.4ghz, ASRock Extreme 4 LGA 2011-v3, 16 gig DDR4, , 3 x Samsung SATA III 500gb SSD, 2X 1 Samsung 1tb 7200rpm outboard, Win 10 64bit, Laptop HP Omen i7 16gb 2/sdd with Focusrite interface. CbB, Studio One 4 Pro, Mixcraft 8, Ableton Live 10 www.soundcloud.com/starise Twitter @Rodein
|
JonD
Max Output Level: -39 dBFS
- Total Posts : 3617
- Joined: 2003/12/09 11:09:10
- Location: East of Santa Monica
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 11:19:00
(permalink)
kzmaier
I am trying to silence my PC. ... I'm looking at the Corsair Carbide Series 330R Ultra-Silent Mid-Tower Case....
My homebuilt PC is dead quiet. Your biggest source of noise is going to be the fans. I have two low-rpm case fans (one intake, one outtake) and a Noctua cpu fan. That's it. My video card (Radeon HD5450) is fanless and easily does the job. The computer case is nothing special, a Cooler Master Centurion. That being said, I ordered a case for a new build yesterday: the Corsair Carbide 200R. I considered the Ultra-silent model, then saw two reviews (@ Newegg) that complained of poor air flow due to the insulation. So I went with the 200R which looks to be identical, just without the extra padding.
SonarPlat/CWbBL, Win 10 Pro, i7 2600K, Asus P8Z68 Deluxe, 16GB DDR3, Radeon HD5450, TC Electronic Impact Twin, Kawai MP11 Piano, Event ALP Monitors, Beyerdynamic DT770 Pro, Too Many Plugins, My lucky hat.
|
kitekrazy1
Max Output Level: -40 dBFS
- Total Posts : 3524
- Joined: 2014/08/02 17:52:51
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 11:30:46
(permalink)
More holes = more noise. Good luck trying to defeat that.
Sonar Platinum, W7 Pro 32GB Ram, Intel i7 4790, AsRock Z97 Pro 4, NVidia 750ti, AP2496 Sonar Platinum, W7 Pro, 16GB Ram, AMD FX 6300, Gigabyte GA 970 -UD3 P, nVidia 9800GT, Guitar Port, Terratec EWX 2496
|
robert_e_bone
Moderator
- Total Posts : 8968
- Joined: 2007/12/26 22:09:28
- Location: Palatine, IL
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 11:52:33
(permalink)
I have a padded case, and I also have a couple of SSD's for primary and for one of my data drives, and that helps. I too keep my case underneath and that helps block a lot of whatever noise is left - and I also have a radiator cooling system, so there is no CPU fan.
The foam on the inside of some cases can really make a difference, but as also posted by others, too many fans can add a bunch of needless noise, though it is always a balance with temperatures. There ARE fans that are quite a bit less noisy than most that come with a stock chassis, and there are additionally rubber mounts for fans, and those keep a lot of noise and vibrations out of being a problem. Those are actually quite cheap - I think they ran about 45 cents apiece, or maybe even cheaper.
Hope any of the above helps,
Bob Bone
Wisdom is a giant accumulation of "DOH!" Sonar: Platinum (x64), X3 (x64) Audio Interfaces: AudioBox 1818VSL, Steinberg UR-22 Computers: 1) i7-2600 k, 32 GB RAM, Windows 8.1 Pro x64 & 2) AMD A-10 7850 32 GB RAM Windows 10 Pro x64 Soft Synths: NI Komplete 8 Ultimate, Arturia V Collection, many others MIDI Controllers: M-Audio Axiom Pro 61, Keystation 88es Settings: 24-Bit, Sample Rate 48k, ASIO Buffer Size 128, Total Round Trip Latency 9.7 ms
|
tlw
Max Output Level: -49.5 dBFS
- Total Posts : 2567
- Joined: 2008/10/11 22:06:32
- Location: West Midlands, UK
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 12:30:58
(permalink)
Foam inside a case helps damp out case vibration and resonance, but because the case can't be sealed it won't reduce fan and drive noise much, if at all.
The route to quiet PCs is large fans operating on reduced voltages, big cpu coolers, quiet or ideally fanless graphics cards, psu built to keep noise down etc.
The PC in my sig has two Noctua 140mm fans, one at the back as an extractor, one on a big Noctua cpu cooler. Graphics and psu are fanless. With the fans running at 7 volts it puts out around 26-28dB at one metre. With the fans running on 5 volts it's so quiet my decibel metre can't measure it.
www.silentpcreview.com is a very useful site for all sorts of information about making PCs quiet. It can be done, but a case change alone won't achieve much.
Sonar Platinum 64bit, Windows 8.1 Pro 64bit, I7 3770K Ivybridge, 16GB Ram, Gigabyte Z77-D3H m/board, ATI 7750 graphics+ 1GB RAM, 2xIntel 520 series 220GB SSDs, 1 TB Samsung F3 + 1 TB WD HDDs, Seasonic fanless 460W psu, RME Fireface UFX, Focusrite Octopre. Assorted real synths, guitars, mandolins, diatonic accordions, percussion, fx and other stuff.
|
Adq
Max Output Level: -82 dBFS
- Total Posts : 426
- Joined: 2015/01/21 20:05:25
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 15:58:10
(permalink)
It seems that Fractal Design is quite popular. I have been choosing between Fractal Design Define R5 and AeroCool DS 200. Tomorrow my R5 should arrive!
|
mettelus
Max Output Level: -22 dBFS
- Total Posts : 5321
- Joined: 2005/08/05 03:19:25
- Location: Maryland, USA
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 18:18:05
(permalink)
Starise
Unless it was specified otherwise, the fans installed are all basic cooling fans...so you might benefit by only changing fans.
Starise's entire post is a good one, and a fan replacement alone may do wonders. Fans collect debris over time that unbalanced them, then degrades the bearings. Aftermarket fans are not expensive, and if rigidly mounted (not too tight) to the case, they should not make much noise. Another thing to check is your BIOS as most have the ability to dynamically adjust fan RPM based on component temperatures. Unless you are running some hard-core plugs with high track counts, "power saving" mode on the MB will cut down fan speed (and noise) considerably unto itself. A larger case with enough air around it to dissipate heat should not be generating excessive noise from the fans. The fans are also good to clean from time to time to ensure they stay balanced.
ASUS ROG Maximus X Hero (Wi-Fi AC), i7-8700k, 16GB RAM, GTX-1070Ti, Win 10 Pro, Saffire PRO 24 DSP, A-300 PRO, plus numerous gadgets and gizmos that make or manipulate sound in some way.
|
Adq
Max Output Level: -82 dBFS
- Total Posts : 426
- Joined: 2015/01/21 20:05:25
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/12 18:32:27
(permalink)
Yeah, noisy fans have to be changed. Also it worth checking if PSU's fan produce any noise, and if it does, it is possible to change fan in the PSU (you just need to be careful, and warranty for PSU will be voided). But if you have HDDs (as me) they will be most noisy thing in the PC after fixing fans. And I think this is what silent cases are for. I hope my new case will help to decrease this noise.
|
kzmaier
Max Output Level: -81 dBFS
- Total Posts : 461
- Joined: 2010/10/18 08:20:01
- Location: Rochester, NY
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/13 08:50:00
(permalink)
Thanks for the tips. This forum is such a great resource!! I have ordered acoustic panels and will check the case fans. The psu fan is the one I was worried about as its not so easy to replace. I'm holding off on the case purchase for now.
Thanks to all!!
|
TerraSin
Max Output Level: -55.5 dBFS
- Total Posts : 1975
- Joined: 2005/08/05 00:27:13
- Location: USA
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/13 11:25:53
(permalink)
I've used both the Corsair Obsidian Series 550D and the Fractal Design R4/R5. Both are very good cases. I think the Corsair has the edge on internal components and I'll probably be buying another one this year but they are both very nicely done. I've been using SilenX fans but going to be putting Noctua ones in the new build.
|
batsbrew
Max Output Level: 0 dBFS
- Total Posts : 10037
- Joined: 2007/06/07 16:02:32
- Location: SL,UT
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/14 15:30:49
(permalink)
i have a Antec Solo Black/Silver Steel ATX Mid Tower Computer Case,
and a Thermaltake TR2 RX W0134RU 550W ATX12V Ver2.2 SLI Ready Modular Passive PFC PFC Power Supply,
has been working quite well for me.
|
tlw
Max Output Level: -49.5 dBFS
- Total Posts : 2567
- Joined: 2008/10/11 22:06:32
- Location: West Midlands, UK
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/14 15:59:13
(permalink)
Fractal Design make very good cases indeed. Mine's the easiest and tidiest PC case to work in I've ever come across.
Sonar Platinum 64bit, Windows 8.1 Pro 64bit, I7 3770K Ivybridge, 16GB Ram, Gigabyte Z77-D3H m/board, ATI 7750 graphics+ 1GB RAM, 2xIntel 520 series 220GB SSDs, 1 TB Samsung F3 + 1 TB WD HDDs, Seasonic fanless 460W psu, RME Fireface UFX, Focusrite Octopre. Assorted real synths, guitars, mandolins, diatonic accordions, percussion, fx and other stuff.
|
sven450
Max Output Level: -72 dBFS
- Total Posts : 945
- Joined: 2004/03/16 08:11:49
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/15 09:16:14
(permalink)
I have used the Antec Solo as well, and if set up properly (as has been mentioned in this thread) it is dead quiet.
|
Reno412
Max Output Level: -90 dBFS
- Total Posts : 28
- Joined: 2015/09/06 11:01:11
- Location: Pittsburgh, PA
- Status: offline
Re: Silent Mid Tower PC cases
2015/10/15 09:44:43
(permalink)
My set-Up is Silent... Also a thing to remember is that BiG fans are very Nice because they do not have to spin as Fast to push lots of air SO, they are very quiet. Small fans spin very fast and are usually Louder. I have: coolermaster HAF X 942 Case, Corsair 1200i power supply, Lamptron Fan Controler, ,1 MSI OC Edition Radeon R9 285 DirectX-12 Gaming Video Card, X79 Express chipset, Intel Core i7-3820 Sandy Bridge-E LGA 2011 130W Quad-Core Desktop Processor Overclocked to 4.6 Ghz, 32 GB (4x8GB Quad Channel) of DDR3-2400+(OC) RAM, Arctic Cooling Freezer I30 CPU Fan, 1 TB Seagate HDD,
Sonar Professional / Windows 10 Pro 64 BitCustom Built Computer by me:Corsair 1200i Power Supply, 1 MSI OC Edition Radeon R9 285 DirectX-12 Gaming Video Card, Intel Core i7-3820, Quad-Core, 4.6 Ghz, 32 GB of DDR3-2400+(OC) RAM, 1 TB Seagate HDD, Monitor: Samsung 60" HD 3D 240Hz Smart-TV Mic: Shure SM57-X2U Guitar: Dean Dimebag Razorback X-Ray Pedal: Line 6 POD HD500X Amp: Crate / 120 Watts / 4- 12" Celestion V-30's
|