RESQ
Max Output Level: -90 dBFS
- Total Posts : 21
- Joined: 2015/01/29 13:40:09
- Status: offline
Standard buffer setting upon opening a project
Hi!
I´ve build an orchestral template and would like my orchestral projects to open every time with a buffer setting of 256 samples to prevent artifacts but it stays on 128 every time I open a project.
Is there anyway to tell SONAR I want to open the project with a buffer of 256?
Thanks!!
|
bitman
Max Output Level: -34 dBFS
- Total Posts : 4105
- Joined: 2003/11/06 14:11:54
- Location: Keystone Colorado
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 00:55:47
(permalink)
I asked for similar yeeeeaaaars ago.
I would like to see the asio buffers and or latency slider when using other access methods saved with each project.
|
scook
Forum Host
- Total Posts : 24146
- Joined: 2005/07/27 13:43:57
- Location: TX
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 00:59:44
(permalink)
ASIO buffer cannot be set by the DAW, it is set by the software supplied by the hardware manufacturer. SONAR just reports the setting.
|
bitman
Max Output Level: -34 dBFS
- Total Posts : 4105
- Joined: 2003/11/06 14:11:54
- Location: Keystone Colorado
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 01:28:57
(permalink)
You can do anything you want to in code if you set your mind to it.
|
scook
Forum Host
- Total Posts : 24146
- Joined: 2005/07/27 13:43:57
- Location: TX
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 01:43:14
(permalink)
Believe that if it makes you feel better.
|
The Grim 
Max Output Level: -76 dBFS
- Total Posts : 724
- Joined: 2016/04/19 02:31:06
- Location: hades
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 02:04:47
(permalink)
you can in studio one, you can have your audio interface driver set to say 128, open studio one, it will report 128, go to options in studio one and change it to 512 or whatever you like, apply, go back to your audio interface driver app and 512 or whatever you set in studio one will be reflected there also
|
35mm
Max Output Level: -68 dBFS
- Total Posts : 1105
- Joined: 2008/12/09 08:21:44
- Location: Devon, UK
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 08:44:16
(permalink)
scook
Believe that if it makes you feel better.
Ha ha 
Splat, Win 10 64bit and all sorts of musical odds and sods collected over the years, but still missing a lot of my old analogue stuff I sold off years ago.
|
35mm
Max Output Level: -68 dBFS
- Total Posts : 1105
- Joined: 2008/12/09 08:21:44
- Location: Devon, UK
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 08:47:13
(permalink)
The Grim
you can in studio one, you can have your audio interface driver set to say 128, open studio one, it will report 128, go to options in studio one and change it to 512 or whatever you like, apply, go back to your audio interface driver app and 512 or whatever you set in studio one will be reflected there also
Isn't that the same as Sonar? It depends if you are using Asio or not. If you are you are, changing the hardware settings via the hardware driver. Asio is just a communication protocol. It's the hardware driver that makes the changes to the hardware.
Splat, Win 10 64bit and all sorts of musical odds and sods collected over the years, but still missing a lot of my old analogue stuff I sold off years ago.
|
The Grim
Max Output Level: -76 dBFS
- Total Posts : 724
- Joined: 2016/04/19 02:31:06
- Location: hades
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 09:30:33
(permalink)
no, not in my experience, it is greyed out in sonar and you must st it via your driver/app for your audio interface. and anytime i change it via the audio interface driver/app while sonar is running the audio engine spits the dummy and stops, where as studio one will keep on truckin whichever way you do it, via studio ones options or via interface driver/app just tried it again to be sure, and to be sure it is  and yes asio
|
35mm
Max Output Level: -68 dBFS
- Total Posts : 1105
- Joined: 2008/12/09 08:21:44
- Location: Devon, UK
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 09:59:08
(permalink)
To be sure to be sure What sound card do you have? I wonder if S1 can do that with all cards. From what I can make out it would need something other than asio to communicate with the audio interface driver in order to change its buffer - I don't think there would be any standard protocol to allow it to do that.
Splat, Win 10 64bit and all sorts of musical odds and sods collected over the years, but still missing a lot of my old analogue stuff I sold off years ago.
|
The Grim
Max Output Level: -76 dBFS
- Total Posts : 724
- Joined: 2016/04/19 02:31:06
- Location: hades
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 10:13:16
(permalink)
reaper also does it, not quite as elegant or automatic as studio one, reaper has a check box in preferences "request block size" you just enter whatever you want 512, 1024, whatever you like, put a tick in the box, hit ok and its changed in reaper and the audio interface driver, reaper also just keeps on truckin without any drop out of the audio engine.
i believe it doesn't matter what audio interface you have, i have several, none of them are presonus units and it's the same with all
|
igiwigi
Max Output Level: -82 dBFS
- Total Posts : 437
- Joined: 2011/04/20 03:37:52
- Status: offline
Re: Standard buffer setting upon opening a project
2017/06/13 10:36:57
(permalink)
Hi Try Midi editing with yamaha Tyros 5 Your hair will fall out Yamaha driver and Sonar hate each other.OR Sys Ex!!! No problems with asio All the best John
|