i use my vstudio 100 with sonar platinum about 3 days. As audio interface and all asio driver things working perfect. But i also want to use it as daw controller. i go control option menu, and i set in and out as vstudio 100 cotrol. But nothing is happens!!! İn vstudio , i selected sonar ect. ect.
 
Has Anybody an opinion? All helps will welcome. :)

nebukenazar
i use my vstudio 100 with sonar platinum about 3 days. As audio interface and all asio driver things working perfect. But i also want to use it as daw controller. i go control option menu, and i set in and out as vstudio 100 cotrol. But nothing is happens!!! İn vstudio , i selected sonar ect. ect.
 
Has Anybody an opinion? All helps will welcome. :)

 
Is the ACT button lit?  Sometimes you have to push the button to get it synced after making sure that "VS100 Control" is set for the control surface settings in Sonar.

Yes the ACT button lit. But still same problem. When i push any button on my vs100, its trigger a midi note rondomly. (ifi load a midi track) İt does not do control things...
 
i am gona load some screenshots in few days.

i have VS-100 working fine in Platinum.  Check edit>preferences>control surfaces
Then:
In Port drop-down arrow: click  Control (VS100)
Out Port drop-down arrow: click  Control (VS100)
(not MIDI VS100)
Apply
OK
Mouse click any transport button in the control bar and the transport buttons on the VS100 light and you're away.  I have to do this if my VS100 is not active after I have started Sonar, but if it is already connected viaUSB when Sonar is started, Sonar remembers the settings.  Works for me.  Good luck!

When you play a MIDI keyboard, do lights flash on your V-Studio control surface?

I just ordered the Cakewalk V-studio 100 used online to work with my Sonar Platinum. I have some questions:
1. Roland.com has the Windows 10 driver 2.0.2 and firmware 1.50 available for download. Is anyone sucessfully using this driver & firmware in Windows 10?
2. Will this setup record up to 8 channels while playing back 6 channels simultaneously?
3. I got the "Sonar V-Studio 100 Hardware Manual.pdf" which has a Block Diagram on page 56. It shows that you can send channels 1-8 pre-comp/EQ or post-comp/EQ via USB 2.0 to the PC before the LEVEL, PAN, & REVERB. While channels 1-8 are sent to the pc via USB, will they at same time be sent to the Main Mix output of the V-Studio?
4. For live performance can you send the mic channels 1-2 to Sonar Platinum to add effects and send it back from Sonar to the Main Mix outputs live? Or will the delay be a problem?
5. Do the track arrow buttons work with Sonar to select other tracks? Can I select a track in Sonar using the mouse and expect the V-Studio fader to now operate for that track selected?

Lots of questions, so little time.  My 100 works perfectly with win 10.  Just hook up the 100 and win will download the drivers and install them. 

FCCfirstclass  Lots of questions, so little time.  My 100 works perfectly with win 10.  Just hook up the 100 and win will download the drivers and install them.  

 
Thanks!  My V-Studio 100 should arrive on Friday USPS.
Ok, just two questions please:

1. For LIVE performance can the mic channels 1-2 be sent to Sonar Platinum to add effects and be send back live from Sonar to the Main Mix outputs?
2. If I use the mouse to select a track in Sonar will the V-Studio 100 fader then operate for that track selected?

 

Does selecting a track in Sonar Platinum cause the V-Studio 100 FADER to operate for that track?

Question one depends on what effects you are using.  A lot of the effects need look-ahead and add a lot of latency.  Not  a problem while mixing, unusable live.  So yes, depending.