Cakewalk Hardware

Cakewalk Hardware (p.37)
Post New Thread
Regular
bnova

V Studio 700 Console and Qty 2 VS700R's- For Sale

All I am selling my V Studio 700 set up including the console and Qty 2 VS700R's. I am moving to a new set up and would like to sell the complete package together. I purchased new about 2 years ago and it has never left my smoke free climate controlled home studio. It is mint condition, probably has..
5
2015/01/16 18:50:35
yoshi030

Roland A-500 Pro Cakewalk + Ableton 9 + Fader

Hello,my problem is that I can't connect the keyboard fader's/knobs with Abelton 9.I did this:I load control map 12 in the keyboard for Ableton 9.Then I pressed MIDI on the Ableton surface.After that I pressed a fader like "Sends" in Ableton and tried to assign the Ableton fader to fader/knobs of th..

2015/01/09 08:19:53
Johnny5078

V Studio 100 and USB 3

Hi I just got a new Alienware laptop with USB 3 ports. The laptop is not recognizing my VStudio 100. Anyone run into this before. I downloaded the Windows 8 drivers and the unit is on Firmware 1.5. Any help would be appreciated. Thanks,John..
4
2015/01/08 12:49:45
clementino

UA-1G mute clean guitar input signal?

hello, I've done a lot of research on this so far, but can't find a solution: I have my guitar plugged into the guitar input of the UA-1G, a pair of active speaker is plugged to the ouput; the ua-1g itself is connected to the usb of the PC; advanced driver is on and - in the control software - the a..
2
2015/01/01 12:15:44
mleghorn

Roland UM-1 -- won't work with Windows 8.1

It stopped working when I upgraded Windows from 8 to 8.1, and I, for the life of me, can't get it to work again. I've tried two driver downloads, um1_w81d_v101.zip (from Roland) and UM1G_Win8_32and64bit_v100.zip (from here), and neither of them work for me. After I plug the UM-1 into my USB (per pro..
3
2014/12/26 07:05:04
guylemec

VS-20 - Unable to read/write data

I have installed VS-20 on W7 64bit twice and continue to get this message when I open the Editor.Also, I try regardless to define Midi I/O devices but, when I Apply/OK the dialog, it insists that I haven't defined any.I have tried USB sockets at the back and on the front of my PC.I have a Saffire Pr..
3
2014/12/21 08:00:08
quad

Mac Driver for CakeWalk SPS-25

If I install the driver of UA-25EX will this work for the SPS-25 on the recent Macbook Pro?..

2014/12/20 17:14:58
Zo

Any controller in the pipeline with Tascam for sonar ?

Question , simple , for the bakers (to replace the VS 700C or as an altrenative to Avid Artist kindastuff ..) thks..
9
2014/12/16 19:04:09
raizen91

Cakewalk SPS-25 Mac Driver?

Can you guys create a driver for cakewalk sps-25 audio interface for Mavericks? Normal mode is okay but I am unable to use midi because advanced mode is not supported in mac. I tried using the driver from Roland but it wouldn't work. thanks!..
2
2014/12/12 02:12:59
Crg

X3 and the VS 700 Set Fantom Midi warning

Hi all, any old timers from the VS-700 crew left? I've been gone a while. I finally put X3 in the DAW and I got the Midi devices aren't set up properly warning for the Fantom Synth. The same as when I went 64 bit with X1d. Putting in the hotfix fixed it. Does the hot fix for the 64bit Fantom work wi..
1
2014/12/09 08:08:46

<< ..37 38 39 ..

© 2025 APG vNext Commercial Version 5.1

Use My Existing Forum Account

Username: Password: Verification:

Use My Social Media Account