Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Running a bass and guitar into the same session of TH3
Is it possible to run a bass and guitar into the same session of TH3. TH3 allows stereo input, can I run the left channel to a Bass Amp, and the right to a guitar amp? And mix together with the TH3 mixer section later in the chain?
|
gswitz
Max Output Level: -18.5 dBFS
- Total Posts : 5694
- Joined: 2007/06/16 07:17:14
- Location: Richmond Virginia USA
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 12:27:18
(permalink)
Why? I definitely run two sessions of th3 at a time.
It seems unnecessarily complicated to do two threads in one instance.
StudioCat > I use Windows 10 and Sonar Platinum. I have a touch screen. I make some videos. This one shows how to do a physical loopback on the RME UCX to get many more equalizer nodes.
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 12:31:00
(permalink)
I'm using stand alone, and the internal looper.
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 12:49:21
(permalink)
With the Markbass Studio, you can click on the input jack and say which input it is, but seems the inout jacks on TH# are just for show.
|
pwalpwal
Max Output Level: -43 dBFS
- Total Posts : 3249
- Joined: 2015/01/17 03:52:50
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 15:28:13
(permalink)
Kamikaze
I'm using stand alone, and the internal looper.
moved to: software  but seriously, surely that's a q for the th3 peeps/forum?
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 15:36:35
(permalink)
|
pwalpwal
Max Output Level: -43 dBFS
- Total Posts : 3249
- Joined: 2015/01/17 03:52:50
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 15:40:16
(permalink)
Kamikaze
What TH3 forum?
fair point
|
abacab
Max Output Level: -30.5 dBFS
- Total Posts : 4464
- Joined: 2014/12/31 19:34:07
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 17:32:59
(permalink)
DAW: CbB; Sonar Platinum, and others ...
|
abacab
Max Output Level: -30.5 dBFS
- Total Posts : 4464
- Joined: 2014/12/31 19:34:07
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 17:40:11
(permalink)
DAW: CbB; Sonar Platinum, and others ...
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 17:55:12
(permalink)
The one is TH3 is fine, just wondered if I could get both channels of my soundcard working within it separately. I set my Korg Nanopad up as footswitch for it. I have it running on my small low powered work laptop.
There's Mobious looper too, which is free and very well laid out. I'm not going to spending money on software for a while. Especially as my Main Music Laptop sits in pieces on the desk of the HP service centre in town awaiting prognosis or post mortem.
It doesn't seem that you can split the left and right of the stereo signal. I went though FX hoping one have a pan control I could manipulate, but there wasn't. I had a little play with using the spitter and setting it so the bass sat beneath the crossover. Kind of of worked, with a little bleed
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 17:59:19
(permalink)
|
Kamikaze
Max Output Level: -45 dBFS
- Total Posts : 3013
- Joined: 2015/01/15 21:38:59
- Location: Da Nang, Vietnam
- Status: offline
Re: Running a bass and guitar into the same session of TH3
2018/08/25 18:29:49
(permalink)
You can change amps with the looper running. It would have been nice just to be able to pick up another guitar, or have a mic running into a clean channel without having to mess around with changing amps. Maybe I could look into setting up a programm change message from the korg nanopad too.
Something I don't see too much of, is two musicians playing into loop pedal at the same time. None of the loop pedals sync with each other.
|