Answered[Solved] Restoring the original REmatrix Solo IRs?

Author
Post
Essentials Only Full Version
msmorris
Max Output Level: -90 dBFS
  • Total Posts : 4
  • Joined: 2014/12/30 18:49:03
  • Status: offline
2017/04/15 06:06:02 (permalink)

[Solved] Restoring the original REmatrix Solo IRs?

So, I'm on a tear, reorganizing my drives -- copying, moving, and deleting items -- and I accidentally deleted an entire folder full of IRs, including my original REmatrix IRs.  Now the stock HALL, ROOM, PLATE, EARLY, SPECIAL options on the REmatrix dropdown just display as disabled.
 
So, what's my simplest restoration?  Can I re-run just one of the 14 or so installation .exes, or must I re-install the entire beast?  I'm hoping for as simple a solution as possible, of course.
 
I'm running SONAR 2015 Platinum on a Windows 10 machine.
 
Thanks for any assistance you might provide me!
post edited by Anderton - 2017/04/21 17:09:53
#1
See best answerList Solutions Only

6 Replies Related Threads
    scook
    Forum Host
    • Total Posts : 24146
    • Joined: 2005/07/27 13:43:57
    • Location: TX
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/15 13:27:35 (permalink) ☼ Best Answerby msmorris 2017/04/21 16:43:59
    REmatrix Solo is in the SONAR Platinum installer. You could manually run the installer or use the Command Center to roll back then update SONAR to get your most recent version back.
    #2
    msmorris
    Max Output Level: -90 dBFS
    • Total Posts : 4
    • Joined: 2014/12/30 18:49:03
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/15 19:32:15 (permalink)
    Thanks for your reply, scook!  Great, I'll try manually running the single installer.  Fingers crossed!
    #3
    Anderton
    Max Output Level: 0 dBFS
    • Total Posts : 14070
    • Joined: 2003/11/06 14:02:03
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/18 15:53:32 (permalink) ☄ Helpfulby msmorris 2017/04/21 16:44:18
    I experiment a lot with the IRs. Once you restore the IRs, save them as a file so you can always bring them back if you alter the IR file used by ReMatrix.

    The first 3 books in "The Musician's Guide to Home Recording" series are available from Hal Leonard and http://www.reverb.com. Listen to my music on http://www.YouTube.com/thecraiganderton, and visit http://www.craiganderton.com. Thanks!
    #4
    msmorris
    Max Output Level: -90 dBFS
    • Total Posts : 4
    • Joined: 2014/12/30 18:49:03
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/21 15:17:51 (permalink)
    Just to report back:  Thanks again to both of you.  Restoring was easy (by just re-executing the Sonar Plat. installation .exe).  I needn't have been worried.
     
    I'm taking the advice to back them up elsewhere, too!
     
    Thanks, gentlemen!
    #5
    scook
    Forum Host
    • Total Posts : 24146
    • Joined: 2005/07/27 13:43:57
    • Location: TX
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/21 15:37:15 (permalink) ☄ Helpfulby msmorris 2017/04/21 16:44:22
    This thread started an adventure for me. Along the way I found innounp, the Inno Setup Unpacker. In most cases it is pretty easy to guess which installer contains a plug-in or some content based on the layout of this page. There are a few bits that are not so obvious. Having the ability to look inside installers helps. This tool works on most CW installers. It is also possible to extract files. The OP needed the FACTORY.rir. In this case re-running the installer was painless. Having the ability to grab individual files from an installer is handy too.
    #6
    msmorris
    Max Output Level: -90 dBFS
    • Total Posts : 4
    • Joined: 2014/12/30 18:49:03
    • Status: offline
    Re: Restoring the original REmatrix Solo IRs? 2017/04/21 16:44:37 (permalink)
    Great stuff, scook!
    #7
    Jump to:
    © 2024 APG vNext Commercial Version 5.1