Tascam us1641 latest driver update v2.07 Anyone using it, yet?

I've just seen this latest Tascam driver for my us1641 I/O.  Is anyone else using it?
I've been tracking and not wanting to test it, till I've got this next batch done.
Tascam us1641 latest driver update v2.07
Michael

My pleasure, Johnny V!
I was going to PM you, and then thought a thread might serve us all, better. 
I think I'm going to install and see what happens even though I am in the middle of tracking extra parts; better acoustic guitars and additional vocals, etc
I've also got my us1641 set up with my laptop out in our breezeway, which is bigger than my control room, where my desktop and 18i20/OctoPre MkII are. All the mics are out there. It's quieter and sounds better being more than 2 +1/2 X the size.
I'll post back after the fact....
Michael

Yeah, not bad at all!
    I bought mine with the confidence of previous Tascam(a 38, then 4 DA38+ 822PCI card and 4 Teac R to R's  before that)gear.So, this customer support is really encouraging!
    I'm hoping for improved RTL, too, but have had no problems with the last driver/us1641 at all and feel as good about it as my 18i20, too.
Michael

At the Normal setting I'm getting 26 ms RTL @ 44.1. 
 
Seems to work fine I opened a Sonar Project and it plays etc. 
So not sure what they changed but, what ever. They usually post a document explaining the updates. And now I'm not sure why they are claiming the W10 Pre 1703 either as it seems to work fine on that.  

My Yamaha 01v only runs at 44.1 so therefore in the past I stayed with that so I could use the SPDIF inputs of the TAscam and then the 6i6. I have changed my set up and now use a Joe Meek 3 Q as my input for vocals, A Fender rumble for bass input. I use the 2 front inputs on the Scarlett for my guitars,, miked or DI'd. I also use small Mackie Mix 8 for cue mix so I don't really use the 01v anymore. 
I highly recommend something like the Mix 8 for monitoring. You can run the 3/4 output into it.  I have a second output from the Joe Meek as well as a second mike on my amp. It allows 100% LOUD control over your cue mix. 
 100's of projects are in 44.1 and I would rather go 48 as I do believe there is a difference but I'm not sure when and where I'd make the swicth over. 
I leave both my interfaces at a middle setting ( 256?)  and never change this. It seems to work for all the stuff I do both tracking and mixing. I haven't had a drop out in years. 
 
I do use a my 01v mixer when I record a live band with the Tascam. 
Because I need compression on certain channels I'll use the 01V for lead vocals, snare, kick and Bass. 
I'll use the SPDIF for the drum overheads because that's stereo.  
I use 11/12  13/ 14 fed from my 4 Aux outs of the 01v. and the SPDIF so there's the back 6 channels. 
Then the front 8 XLR get guitar amps, back up vocals and other drum mikes, The 9/10 I've used for acoustic guitar and Amp TRS DI outs.  Keyboards use the midi so there's all 17 channels. I also might use a stereo USB board mix feed and run Sonar in WDM mode ( now WASAPI ) so projects can have 18 audio tracks.  
 

Oh wow, I thought they had long stopped updating this. I'm using an old version after tyring them all this was the only one I could get to work. Not without its issues though. I have to have the computer on a few mins before turning the tascam on or I get a blue screen of death.

I might try this new version though. Cheers.

Adji
Oh wow, I thought they had long stopped updating this. I'm using an old version after tyring them all this was the only one I could get to work. Not without its issues though. I have to have the computer on a few mins before turning the tascam on or I get a blue screen of death.

I might try this new version though. Cheers.

 
I have used my us1641 with at least 12 different computers from XP 32 bit up to the latest W10 64 bit. Under XP there where issues which in retrospect where probably the computer not the interface. But as a rule it never gave me problems. I bought my Scarlett 6i6 strictly for portability and at this point there is little difference in performance or stability between the 2 interfaces..  
 I've never had a blue screen and I always leave mine turned on. Try a different USB port.