X2 automation does not work -

Author
Post
Essentials Only Full Version
rir1
Max Output Level: -89 dBFS
  • Total Posts : 93
  • Joined: 2004/11/04 15:34:20
  • Status: offline
2014/07/09 23:54:33 (permalink)

X2 automation does not work -

thought I'd post again, maybe someone new is viewing and has a thought - my faders are not recording automation in X2.  I can draw nodes and move those and X2 sees them; but if I move the faders the data is not recorded (and it doesn't override the nodes, like it used to).  I am read enabled and write enabled.  Never had any trouble with volume moves for automation before in Sonar - again, I can draw volume moves - but the fader moves do not get recorded - what's the problem?
#1

3 Replies Related Threads
    brconflict
    Max Output Level: -56.5 dBFS
    • Total Posts : 1891
    • Joined: 2012/10/05 21:28:30
    • Status: offline
    Re: X2 automation does not work - 2014/07/10 12:39:05 (permalink)
    Do a test in a different project (or a new project). I've seen cases in the past where something inside the project gets 'corrupted' and causes issues, but it's only within that one project. If that's the case, you may just need to delete that whole envelope and try again. I've had similar issues with Gain Automation envelopes not responding to clicks, and the only way I could escape that was to create a new track, copy over the audio and start fresh with a new Gain Automation envelope. 
     
    Hope this helps!

    Brian
     
    Sonar Platinum, Steinberg Wavelab Pro 9, MOTU 24CoreIO w/ low-slew OP-AMP mods and BLA external clock, True P8, Audient ASP008, API 512c, Chandler Germ500, Summit 2ba-221, GAP Pre-73, Peluso 22251, Peluso 2247LE, Mackie HR824, Polk Audio SRS-SDA 2.3tl w/upgraded Soniccraft crossovers and Goertz cables, powered by Pass-X350. All wiring Star-Quad XLR or Monster Cable. Power by Monster Power Signature AVS2000 voltage stabilizer and Signature Pro Power 5100 PowerCenter on a 20A isolation shielded circuit.
    #2
    gswitz
    Max Output Level: -18.5 dBFS
    • Total Posts : 5694
    • Joined: 2007/06/16 07:17:14
    • Location: Richmond Virginia USA
    • Status: offline
    Re: X2 automation does not work - 2014/07/10 13:00:48 (permalink)
    Offset mode?

    StudioCat > I use Windows 10 and Sonar Platinum. I have a touch screen.
    I make some videos. This one shows how to do a physical loopback on the RME UCX to get many more equalizer nodes.
    #3
    rir1
    Max Output Level: -89 dBFS
    • Total Posts : 93
    • Joined: 2004/11/04 15:34:20
    • Status: offline
    Re: X2 automation does not work - 2014/07/10 14:21:35 (permalink)
    thank you Brian, that's it!  I had suspected something like that, but I wasn't going to go as far as a new project - I cloned a track with no change - but when I created a new project and pasted stuff in, it worked.  Will be a pain with some large old projects, but at least I know the software is working.  Thanks, man.  And also to Gswitz, I saw about offset mode in a previous post but it didn't work, but I thank you for helping me figure it out.  What a great community!  Thanks again.
    #4
    Jump to:
    © 2025 APG vNext Commercial Version 5.1