H/W Outs

Re: H/W Outs (cpkoch)

Sun, 09 Dec 2018 22:47:57 GMT

Thanks everyone for your help!

Re: H/W Outs (Cactus Music)

Sun, 09 Dec 2018 17:05:50 GMT

It's always been there but usually hidden. In the Console view if you go to the right, drag your output busses ( Master etc) over to the middle then go back to the far right edge until you get a double arrow cursor, now hold and drag it into view.
It will also show in the track inspector if you have no tracks in a project, open the blank project template. You'll see the Master buss and the Interface buss. 99% of the time we don't need to see them or make changes. Only if you have a multi output interface and you are using those for outboard processing or headphone mixes.

Re: H/W Outs (57Gregy)

Sun, 09 Dec 2018 15:25:26 GMT

The H/W outs has been there for a long time. It used to me called 'Mains'.
You should be able to hide/show it with a button or one of the preferences.

Re: H/W Outs (Jesse G)

Sun, 09 Dec 2018 04:54:26 GMT

So your Master bus has the Yamaha Steinberg AI unit listed as Output.
Then delete the Metronome and Preview Bus and add them back.
Select the Yamaha Steinberg AI unit a their outputs and you should be fine.
Click Save.

Re: H/W Outs (cpkoch)

Sun, 09 Dec 2018 01:47:24 GMT

Thanks for your prompt reply. Because I don't remember ever seeing this bus before is it something new to CbB or has it been well hidden over the years?

For whatever it is worth, I followed your instructions and started a new CbB session, set up the Normal template and looked for the H/W OUts bus and could not locate is in the Console view. I saved the template with a unique name.

I hit the letter "P" and found the Yamaha Steinberg AI unit for both Input and Output.

When I go back to the session during which I have the error message and the H/W Outs issue... that both remain. Should I dump that effort and start anew? or is there a way of fixing it?

Re: H/W Outs (Jesse G)

Sat, 08 Dec 2018 23:00:36 GMT

Just make sure that your buses are assigned to the outs of your Audio I/O.
Select the Master Bus and select Output 1/2
Select the Metronome Bus and select the Out for that
Select the Preview Bus and select the Out for that.

Check your normal Template or your startup template and check the outputs for that Template and then re-save the template.
~~ Also ~~
With Cakewalk Opened, Hit the letter "P"
Check you devices to make sure your I/O drivers being used are selected.

Re: H/W Outs (Bristol_Jonesey)

Sat, 08 Dec 2018 22:51:56 GMT

That bus is your route to the outside world and is connecting to, I would, guess, some sort of Yamaha device (interface probably)

You must ensure that ALL other busses route eventually to this bus, either directly or via a number of intermediate busses.

it is the one bus which any version of Sonar will create automatically for you when you start a new project
All other busses must be created by you (or via a template)

H/W Outs (cpkoch)

Sat, 08 Dec 2018 22:28:34 GMT

Maybe it;s been there right along but I seem to have somethignner in the Console View. It's called H/W Outs. This coupled with an error message when I open SPLAT that suggests my Master, Metronome, and Preview buses are all connected to silent hardware is giving me fits. The only "bus" that I am able to get sound out of is the one that is titled H/W Outs that has in the track labe the Term "YmhStUAU2201L". It's been a while since I've used SPLAT (or CbB for that matter) but I don't recall ever having seen that "bus" show up, and have problems such as I am experiencing now. Any suggestions are welcomed!